BeautySkin Manual Excerpt

Note: Please read the Users Guide thoroughly before start-up and make sure to keep available for ready reference.

Introduction

 What is BeautySkin, and what does it do?

• BeautySkin is a highly effective procedure for cosmetic treatment of pimples and blackheads.

• BeautySkin is based on the positive effect that light of certain wavelengths has on human skin.

• Blue light penetrates the skin to the bacteria (proprionibacterium acne) which causes pimples and blackheads.

• It has an antibacterial effect and prevents the further development of pimples and blackheads.

• Red light soothes skin inflammations and relaxes and stimulates the skin in a positive way.

• The combination and the simultaneous application of both color types of light create the special effect of BeautySkin.

• BeautySkin works without UV radiation.

 Safety instructions 

• Before undertaking any work on the unit, pull the power supply plug out of the socket.

• Do not set up BeautySkin in wet/moist areas, or in bathrooms or near a swimming pool.

• BeautySkin may not be operated in areas subject to explosion hazard.

• Always use the protective eyewear provided during application of BeautySkin.

• Make certain that the distance between lighting tubes (lamps) and the affected skin areas to be irradiated is at least Four Inches (10 cm.)

• Please note: Certain medications can influence the general reaction of the body to light. In case of questions, please consult your physician.

• If you notice any unpleasant skin reactions after or during the application of BeautySkin, stop the application immediately and consult a dermatologist.

• Do not touch the lamps during the application. After completion, pull the power supply plug out of the socket.

• Allow BeautySkin 10 cool (about 15 min) before storing the unit in a closed container (i.e. in the ori­ginal packaging).

• Do not open the housing of BeautySkin. Repairs in and on the unit should be done only by our customer service technicians.

• Before changing the lighting tubes (lamps), please pull power supply plug from the socket

• Use only a moist cloth to clean BeautySkin and do not submerge the unit in water.

• Electrical appliances are not toys. Keep BeautySkin out of the reach of children.

Connection to power supply

• Before start-up, be sure that the country-specific supply voltage matches the operating voltage listed on the output plate of the unit.

Instructions for use

• Set BeautySkin up for use on a firm surface at suitable height.

• Cleanse the affected areas of skin with a pH-neu­tral soap and dry the skin thoroughly.

• During the application of BeautySkin, no cosmetic residues should remain on the skin. Do not use tanning lotion!

• The effect of BeautySkin is not achieved through UV radiation.

• Insert the power supply plug from the BeautySkin unit into the socket.

• Put on the protective goggles and seat yourself in front of BeautySkin with the affected skin areas at about Six Inches (15 cm) from the unit.

• Turn the adjusting knob of the timer towards the right until the pointer indicates the desired application time.

• This turns on BeautySkin and activates the timer. After the set time has run out, BeautySkin will automatically shut off.

• A worsening of symptoms at first is normal and an indication of effectiveness.

• For an optimal result we recommend a daily treatment of 15 minutes fore each of the affected skin area.

• Relax and allow the light to develop its effect on your skin.

• After using, pull the power supply plug out of the socket.

• After the application of BeautySkin, we recommend that you apply a non-greasy lotion to the treated skin areas.

• You will achieve the best results if you use BeautySkin for 15 minutes daily on each affected skin area over a period of at least 8 weeks.

• Regular use is of decisive importance for effectiveness. Optimal results are generally achieved after 12 weeks.

Service life of the lamps

• Dr. Kern Special Fluorescent Lamps) have a maximum service life of 400 hours. After this time they still glow; however, the radiation is weakened to such a degree that the tubes should be replaced.

Lamp Replacement

• Replacement is easy and is done as follows: (please use only original Dr. Kern Lamps)

• Unplug the unit..

• Unscrew the 4 fastening bolts on the back panel of the unit and remove the panel.

• Turn each lamp as far as necessary to enable it to be removed towards the front from the base slots.

• Replace with new lamps by pushing the contact pins above and below into the base slots at the same time and finally turning the lamps one quarter turn on their axes.

Replacement of the starters

• It is very easy to replace the starters. The starters should be renewed along with every lamp replacement. The starter is removed from its base through light downward pressure and minimal rotation to the left.

Maintenance

• Before all cleaning and fluorescent tube changes, always be sure to pull the power supply plug from the socket.

• Wipe the tubes and the reflector regularly with a dry, soft cloth.

• The red and blue fluorescent tubes were especially developed with the required wavelength for BeautySkin.

• Lamps are available only from Dr. Kern. and its authorized distributors.

• The fluorescent tubes should be replaced after 250 operating hours.

Warranty

• The BeautySkin is warranted for 12 months from date of shipment.

Technical data

Supply Voltage:           110V 60 Hz (USA Model)
Lamp type:                  Dr. Kern Special Fluorescent Lamps
                                  Blue (spectrum 400-450 nm)
                                  Red (spectrum 580-659 nm)
Power of each Lamp:   15W
Lamp Length:              11.5” Approx (29cm)
Number of Lamps:        6 (Three Red and Three Blue)
Power Consumption:    Approx 100 W